)
Materiales:
Materials:
- Cartón de huevos.
- envase de refresco.
-envase de vidrio ( mayonesa).
-tijeras.
-pincel.
- silicon frió y caliente.
- pintura al frió color amarillo.
- pintura de caucho o de pared.
- Escarchas
- pega blanca.
- Egg carton.
- soft drink container.
- Glass container (mayonnaise).
-scissors.
- Paintbrush.
- hot and cold silicone.
- yellow cold paint.
- rubber paint or wall paint.
- Frost.
- white glue.
Realizacion:
Realization:
1- Primer paso tomè el cartón de huevo y lo corte en tiras largas y recorte cada triángulos que contiene y lo redondee con las tijeras.
1- First step take the egg carton and cut it into long strips and cut out each triangle it contains and round it with the scissors.
2- Coloque cada triángulo ya cortados y comencé pegar en mi envase de vidrio con silicon frió en forma circular.
2- I placed each triangle already cut and began to glue it in my glass container with cold silicone in a circular shape.
3-Luego comencé a pintar de blanco el envase ya con los triángulos pegados utilice la pintura de pared para dar un fondo blanco a mi envase y tapa para que fuera fácil agarrar el color amarillo después.
3-Then I started to paint the container white and with the triangles glued I used the wall paint to give a white background to my container and lid so that it would be easy to pick up the yellow color later.
4- El envase y tapa al estar previamente secado con la pintura blanca paso a pintarlo de amarillo completamente.
4-The container and lid being previously dried with the white paint, I paint it completely yellow.
5-Luego tomè el envase de refresco y recorte por la mitad con un cuchillo caliente y redondee con la tijera hasta que me quedo un cilindro.
5-Then take the soda can and cut it in half with a hot knife and round it with the scissors until I had a cylinder.
6- tomè mi cilindro y recorte por la mitad y comencé hacer tiras pero sin recortar todo solo hasta la mitad y cada tira la enrolle para que me quedara la forma de las hojas de una piña se recortan 2 para luego enrollar y dejar una abertura que entre en el agujero de la tapa de mi envase primero se coloca un cilindro y el otro se coloca adentro del ya pegado a la tapa.
6- I took my cylinder and cut it in half and began to make strips but without cutting everything only halfway and each strip I rolled it so that it would be the shape of the leaves of a pineapple, 2 are cut and then rolled and leave an opening that fits into the hole in the lid of my container, first one cylinder is placed and the other one is placed inside the one already glued to the lid.
7- Para finalizar agarre el envase y en cada punta de los triángulos le aplique un poquito de pega blanca y le rocié escarchas para darle un toque de brillo.
7- To finish, I took the container and applied a little white glue on each end of the triangles and sprinkled frosting to give it a touch of glitter.
❤️Fue un placer compartir este post espero que les guste mucho..❤️
❤️It was a pleasure to share this post, I hope you like it very much...❤️
photos taken with blue studio phone.
Gifs made with PfotoScape.
Congratulations @genice! You have completed the following achievement on the Hive blockchain and have been rewarded with new badge(s) :
Your next target is to reach 4250 upvotes.
You can view your badges on your board and compare yourself to others in the Ranking
If you no longer want to receive notifications, reply to this comment with the word
STOPCheck out the last post from @hivebuzz: