My introduction to Hive Diy/ Mi introducción a Hive Diy, abstract sculpture made from old oak wood/ escultura abstracta hecha con madera de roble vieja(ESP/ENG)

in Hive Diy3 years ago

Hello everybody!
Due to the first hours of sun yesterday I had gotten quite creative and spent the whole day making this sculpture.
IMG_1624.JPG

Short about me: During the last two years (during the Corona Pandemics)
I really got into making sculptures out of old oak wood and discovered my creative side while doing so.

Today I want to show you my last work: an abstract sculpture made from an oak wood bar (about 250 years old).

But first let's start with the fabrication:
IMG_1597.JPG

IMG_1598.JPG

IMG_1599.JPG

IMG_1600.JPG
Those pictures show the bar in it's original shape.
First I took a drill with an attached steel brush and cleaned the bar.
Then I roughly shaped it with the chainsaw.
IMG_1602.JPG

IMG_1601.JPG

Afterwards I took an angle grinder to bring out some details.

IMG_1611.JPG

IMG_1607.JPG

IMG_1604.JPG
The pictures show the bar edited with the angle grinder

And finally I brought out fine details with the plate grinder.

IMG_1618.jpg

And after round about 10 hours of work it was finally finished:

IMG_1628.jpg

IMG_1635.JPG

IMG_1632.JPG

IMG_1631.JPG

IMG_1626.JPG
Thanks for reading and I hope you liked it.
If you want to you can leave some feedback in the comments.
See you soon

ESP:
¡Hola a todos!
Debido a las primeras horas de sol de ayer me he puesto bastante creativo y he pasado todo el día haciendo esta escultura.
IMG_1624.JPG

Breve sobre mí: Durante los últimos dos años (durante la Corona Pandémica)
me aficioné a hacer esculturas con madera de roble vieja y descubrí mi lado creativo mientras lo hacía.

Hoy quiero mostraros mi última obra: una escultura abstracta hecha con una barra de madera de roble (de unos 250 años).

Pero primero vamos a empezar con la fabricación:
IMG_1597.JPG

IMG_1598.JPG

IMG_1599.JPG

IMG_1600.JPG
Esas fotos muestran la barra en su forma original.
Primero cogí un taladro con un cepillo de acero acoplado y limpié la barra.
Luego le di una forma aproximada con la motosierra.
IMG_1602.JPG

IMG_1601.JPG

Después cogí una amoladora angular para sacar algunos detalles.

IMG_1611.JPG

IMG_1607.JPG

IMG_1604.JPG
Las fotos muestran la barra editada con la amoladora angular

Y finalmente he sacado detalles finos con la amoladora de placas.

IMG_1618.jpg

Y después de unas 10 horas de trabajo por fin estaba terminado:

IMG_1628.jpg

IMG_1635.JPG

IMG_1632.JPG

IMG_1631.JPG

IMG_1626.JPG
Gracias por leer y espero que os haya gustado.
Si queréis podéis dejar alguna opinión en los comentarios.
Hasta pronto

Sort:  

Saludos, siempre he tenido un gran respeto por las obras de arte, espero ver más de su trabajo, le deseo mucho ánimo y buena suerte con el post.

Gracias muchos!

Congratulations @fishsphilaworld! You have completed the following achievement on the Hive blockchain and have been rewarded with new badge(s):

You received more than 1000 upvotes.
Your next target is to reach 1250 upvotes.

You can view your badges on your board and compare yourself to others in the Ranking
If you no longer want to receive notifications, reply to this comment with the word STOP

Check out the last post from @hivebuzz:

Hive Power Up Month - Feedback from February day 11
Valentine's day challenge - Give a badge to your beloved!
Support the HiveBuzz project. Vote for our proposal!